Carbon distortion: The Story
Interested in what carbon distortion and quantum mechanics means for your tone? Check out the video below that covers the inception, purpose, difference, and potential applications of "quantum tunneling" and carbon clipping with Nanolog Devices:
...Need to know more? We know one 16 minute video likely won't answer everything that comes to mind. So please, leave some comments and questions below to give us some food-for-thought for our next video!
You can also head over to Delicious Audio for a quick read Q&A session with our President & Co-Founder, Adam Bergren, here.
Lots of exciting press today! The WaveFunction Overdrive is now available in limited quantities through our online store. We're actively looking for dealers to distribute our products locally - so please contact us.
So, just What is Molecular Electronics? And how can it be used to create something interesting?
The field of molecular electronics got going when the idea of using a molecule as a circuit component was proposed theoretically in 1974. Since then, there have been many experiments aimed as using molecules in circuits. Many of these use layers of molecules (not just a single molecule), and due to the way devices are constructed (see Figure 1 below), the critical dimension of the device resides in the same range as many small molecules (2-50 nm).
Figure 1 shows a molecular junction:
Figure 1 shows to conductive layers with a molecular layer between them. In this case, a layer of ~2 nm is shown (2 molecules thick).
So, the main component, the Molecular Junction, is really a nano molecular sandwich, with conductors as the bread.
In order for electrons to complete the electronic circuit between the two conductors, they must flow across or through the molecular layer, meaning that a molecular junction incorporates molecules directly into the circuitry.
What does a molecular junction look like? Figure 2 shows a SIM card containing two molecular junctions in an adapter designed to enable electrical contact to the devices.
Figure 2: Photograph of a molecular junction:
The molecular junctions shown above can be integrated into analog circuitry easily by putting a SIM card holder onto a PCB board with the rest of the circuit.
OK, here are NAI clipping prototypes loaded with molecular junctions and 1N4148 pairs ready for direct comparison:
Time to put the Nanolog Audio Inc. Studio Measurements Lab to work!
In order to determine how molecular junction clipping differs from conventional diode clipping, we run a 0.3 Vpp (that's peak-to-peak) at 220 Hz into the input. Then, the output is put into an oscilloscope. As the settings on the pedal are changed, the output is monitored. Finally, in order to capture the waveforms and do further analysis, Audacity is used to record several seconds of the waves, and the data exported for plotting.
Here is a direct overlay of the resulting waveforms, showing an offset comparison of the input sine wave with the resulting clipping from a conventional 1N4148 diode pair and two different molecular junctions, one of which is 5 nm thick, and the other which is 8 nm thick:
Two things are notable right away: the shapes are different, and the heights are different.
First, let's tackle peak height. These data were captured without adjusting the volume knob in order to show the relative amplitudes of the clipped waveforms. This is because the height of the waves will determine the overall volume, and the simple process of switching the clipping device can have a big impact on volume. As well, this height will determine the amount of dynamic range available for the player to interact with. The lower the wave height, the more compressed the signal is, and it can end up sounding "squished," which has an important impact on the tone and touch sensitivity- typically the end result of a more compressed clipped signal is less interactive feel, which is not inherently bad, but certainly different. It will depend on the intent of the player if this is desirable or not.
Second, let's get to the shapes. The more squared-off the waveform is, the more saturation or distortion there will be. That is because if we transform the time domain signal shown above into the frequency domain (more on that later), we could consider a square wave mathematically as an infinite sum of sine waves with different frequencies- this creates a very "saturated" sound perception, as if all of the available space is filled with noises.
The above data are transformed using Audacitiy's FFT algorithm, which is some fancy math that let's us see the individual frequencies the wave is composed of. For this type of clipping, we typically get harmonics- that is, integer multiples of the fundamental tone, which is 220 Hz. We therefore expect to see 220 Hz as the highest intensity, followed by 440, 660, and so on.
There are two things to note about the waveforms: a 5 nm molecular junction produces more compression and a more squared-off wave than an 8 nm molecular junction, and both of these show greater peak heights and more rounded shapes than the diode clipping.
Now, to the transform of these waveforms into the frequency domain, where we can check on how that initial single 220 Hz sine wave made out on its way through the clipping circuit:
Here, we see at far left the first peak, which is at 220 Hz (or 0.220 on this plot, where I've used kHz as the unit).We see that the diode clipping results in the most saturated frequency space, as expected from the waveforms. Both molecular junctions produce less saturation, and the frequencies fall off in intensity more as the frequency increases (follow the tops of the peaks and you'll see the steeper slope in the case of the molecular junctions. It is a bit harder to see a difference between the two molecular junctions, but it is there (I'll have to plot the heights sometime separately to show this more explicitly, but for now, this makes the point). The prediction we make from these plots is that molecular junction clipping will result in a "warmer" tone, with less high frequencies inherent, but at the same time with more dynamic range and less compression. Really cool combination!
What does this all mean? It means there is greater control over frequency space due to the nanoscale engineering of the devices used in the clipping circuit! The differences we hear in the sound, and that we can feel when playing through the circuit with different clipping devices is indeed measurable, and now we have some extra tonal colours with which to create soundscapes: an end result that we hope is the nano-enabled musical expression of diverse ideas!
Here are some YouTube videos that show the core technology of Nanolog Audio in action!
First up is a basic demonstration after a description of the technology:
BASIC TECHNOLOGY AND DEMONSTRATION
Next up, there is a demonstration of the use of the clipping prototype in a musical context, include a really great original song composed by Nick Jaffe. You can buy his album HERE that features this song!Next up, there is a demonstration of the use of the clipping prototype in a musical context, include a really great original song composed by Nick Jaffe. You can buy his album HERE that features this song!
DEMONSTRATION IN MUSICAL CONTEXT